News

LF-CF18 New Qi Dual Coil 10W Wireless Fast Charging Input: 5V=2A 9V=1.67A Output: 5.0V/1.5A 9V/1.35A Line length: 1M Conversion rate:>73% Material: ABS environmentally friendly material product Size: Height 120 * Width 80 * Length 100mm Color: Black/Red/Blue/Gold Chip: imported Input: 5.0V/2A9.0V/1.67A Output: 5.0V/1.5A9.0V/1.35A Charging distance: 2-10MM Conversion rate:>73% Charging frequency: 110-205KHZ Executive standard: QI wireless charging standard characteristic ABS fireproof material True resistance to falling and high humidity Dual heat dissipation mesh True heat dissipation without burning Silicone gasket True anti slip and non falling Early entry into the wireless era 2.8 hours full No injury/machine damage/no burning

Basic parameters Basic Parameter "Earphone size (mm) L * H=55.2 * 25.8mm Weight Earphone: 2 * 18g+Charging: 80g Color: Available in four colors: black, orange, white, and pink; Major function "Bluetooth calls, Bluetooth music, Supports SBC, AAC code music[ Hardware parameter Bluetooth chip manufacturer (Chipset Supplier) Jerry Chipset AC7006F4 Compatible System IOS and Android FLASH memory N/A Amplifier board amplifier N/A Connection parameter BT BT5.3 WIFI N/A NFC N/A Speaker/microphone speaker model f15.4 inch speaker/15.4 DRIVERS Microphone model silicone label Battery Battery Type Polymer Lithium Capacity earphones: dual 65mAh, charging compartment: 400mAh Charging Method Type-c charging, earphone magnetic suction charging Process material: charging compartment+earphone body: ABS/earhook: silicone+steel wire Other parameters Other Partmeter "Waterproof Level IPX4 Charging time about 90 minutes Life time 60% volume IOS, as long as 6 hours Product language English Appearance material ABS

Product description LF-A80 is an internationally leading and cost-effective three in one wireless charging solution that achieves efficient wireless transmission Can; Conversion efficiency up to 80%, maximum transmission distance up to 5mm, support for Apple 12 phone pop-up, support for 5W/7.5W/10W/15W Wireless charging, supporting PD and QC3.0 protocol fast charging adapter, can charge all wireless charging phones that meet QI standards. This product Can simultaneously charge mobile phones, Apple headphones, and Apple watches. Technical parameters Charging method: electromagnetic induction Input voltage and current: 9V/3A Double coil wireless charging output power: 5W 7.5W 10W 15W Apple earphone wireless charging output common rate: 3W (maximum) (test bench test 5W) Apple watch wireless charging output power: 1-2W Maximum total output power of the entire machine: 22W No load power consumption:<1W Effective transmission distance:<5mm Conversion efficiency:<80% Operating frequency: 105~205KHz Protection measures: foreign object detection, over temperature protection, over current protection, under voltage protection, short circuit protection, over voltage protection High conversion efficiency and cost-effectiveness Product modet: JJT-A80 Charging mode: electromagnetic induction Input voltage current: 9V/3A Dual coil wireless charging output power :5W 7.5W 10W 15W Apple earphone wireless charging output common rate: 3W(Max) Apple Watch wireless charge output: 1 - 2W The maximum total output power of the machine:22W No-load power consurmption: <1W Effective transmission distance: <5mmConversion efficiency:<80% Operating frequency: 105-205KHz Protection measures: foreign body detection, over temperature protection,over current protection, under voltage protection,Short circuit protection, avervoltage protection

Product description ProductInformation Model: A77 Battery capacity:10000mAh Color: black, silver, gray, purple Protection circuit: Yes Material: PC+ABS Size: 104*68*19mm Compatibility: 99% smartphonesand tablets Output: 22.5W+15W wireless charging Magnetic suction+wiredPower Bank2-in-1 LED intelligent digital display 22.5W Super Fast Charge 15W magnetic suctionwireless charging PD 20W bidirectionalfast charging 25 Mobile phone holdervertically and horizontally rechargeable 1. Standby state (sleep state): In standby mode, briefly press the button once, and the nixie tube will display the current percentage of electricity. At the same time, the boost circuit will work and the output will be turned on. If there is no load for 40 seconds Turn off the left and right digital tubes and turn off the output, and the entire machine enters standby mode; 2. Charging status (display current battery percentage) A. When the TYPE-C port is connected to an external power source, the digital tube displays the current battery level and flashes to indicate charging. After fully charging, the digital tube displays 100%. 3. Power on status (display current battery percentage, start boost output): A. After pressing the button, the nixie tube displays the current percentage of battery power. If there is no load or the load is less than the maintenance current of 50mA (+/-30mA), at a certain time After the boost is turned off, the digital tube goes out and enters a sleep state. If the load is greater than 50mA (+/-30mA) or above, please refer to "Discharge Status" for details. 4. Discharge state, load greater than 50 mA (+/-30mA): A. Single port output supports fast charging. B. Multiple ports output simultaneously, does not support fast charging.

specification 1 Basic ParameterEarphone size Earphone size L*W*H= 116*109*46mm Weight 18g Color black.green.orabge Major function bluetooth calls,music, supprot SBC,AAC code music. 2 Hardware parameter Chipset Supplier Chipset AB5656B2 Compatible System IOSandroid FLASH memory N/A amplifier N/A 3 Connection parameter BT BT5.3 WIFI N/A NFC N/A 4 Speaker/microphone speaker f14speker /14 DRIVERS microphone FH2718T(full direction microphone) 5 Battery Type polymer lithium Capacity 90mAh Charging Method Type-c 6 technology material subject ABS,Titanium nickel memory steel wire for hanging rope 7 Other Partmeter Waterproof Level IPX4 Charging time about 90 minutes Life time 60% volume IOS, as long as 10 hours Product language English Appearance material ABS 8 Package Size Packaging box size(L*W*H)MM Tiandi Gai 15×13x5cm pakeage weight(g) 100g carton size(L*W*H)CM 590*375*400mm outer box weight(KG) 8.5kg packing quantity(platform) 60

Product Parameters brand Lu Feng/LUFNG name CPU heat sink Fan size 120 * 120 * 25mm support Intel/AMD Universal Air volume 48CFMMin bearing Hydraulic bearings voltage 12V DC current 0.23 ± 10% A speed 1000-2000RPM10 (4-pin plate) 2000RPM ± 10% (3-pin plate) Socket Motherboard with three or four pins available noise 18-20dB (A) Mute power With light 4~6W life 50000 hours

Product specification parameters Anti freezing -38C non-conductive water-cooled liquid Water discharge Water discharge size: 274 * 120 * 27mm Appearance/Function: Black/12 Waterway Material: Aluminum Fan Fan size: 120 * 120 * 25mm Fan speed: 800-2000+/-10% Air volume: 30-75CFM Bearings: Hydraulic Control: 4pin (PWM)+3pin RGB Input voltage: DC12V Noise: 25-32dBA water pump Platform: Intel: LGA2066/2011V3/2011/115X/1700AMD: AM5/AM3+/AM3/FM2+/FM2 Size: 69 * 69 * 96mm Speed: 2200+/-10% Input voltage: DC12V Noise: 23dBA

Product parameters Brand: LUFNG Name: CPU heat sink Air volume: 48CFMMin Fan size: 120 * 120 * 25mm Support: Intel/AMD Universal Voltage: 12V DC Bearings: hydraulic bearings Current: 0.23 ± 10% A Speed: 800~1800RPM ± 10% (4 needles) 1500RPM ± 10% (3 needles) Socket: motherboard with three or four pins available Noise: 18-20dB (A) Mute Power: 4~6W with light Life: 50000 hours FIN technology for penetrating 6 pure copper heat pipes Efficient heat dissipation of tower type sheet group The heat generated by the CPU is transmitted through pure copper heat pipes to a large area of vinegar flakes to disperse the heat, and the fan blows in cold air to remove the heat from the flakes

Product parameters Brand: LUFNG Support: Intel/AMD Universal Design Fan: 120 * 120 * 25mm 90 * 90 * 25mm Bearings: hydraulic bearings Air volume: 48CFMMin Voltage: 12V DC Current: 0.23 ± 10% A Speed: 1600RPM ± 10% cm 2000RPM ± 10% cm Power: with lamp 4-6 W Life: 50000 hours Noise: 18-20db (A) Mute Socket: motherboard with three or four pins available

Product description Product specification parameters Product size: 123X123X63MM Fan size: 90X90X25MM Fan speed: 2000PRM ± 10% Interface: 3PIN Bearing type: hydraulic bearing Noise: 23DBA ± 10% Rated voltage: 12V.DC Air volume: 38CFM Expected life: 40000H Rated current: 0.2A Downblow design for effective heat dissipation The down blowing design can effectively reduce the CPU temperature and take away the hardware temperature around the motherboard, suitable for CPUs with power not exceeding 95W Faster heat dissipation during compaction process Each thread piece is polished by side pressure, and the heat transfer loss between each thread piece is greatly reduced by using a pressing process to stack and tightly contact each other, achieving rapid heat dissipation

Product parameters Brand: Lufeng/LUFNG Overall size: 120 * 120 * 78mm (length, width, height) Fan: 120 * 120 * 25mm /90 * 90 * 25mm Bearings: hydraulic bearings Speed: 1600/2000 soil 10% Socket: motherboard with three or four pins available Support: Intel/AMD Universal Design Air volume: 48CFMMin Voltage: 12VDC Current: 0.23 ± 10% A Power: with lamp 4-6 W Life: 50000 hours Noise: 18-20db (A) Mute

Product Information Name: Brand: Lufeng/Lufeng Overall size: 100 * 92 * 67mm Fan: 90 * 90 * 25mm Power parameter: 12V Interface power supply: 3Pin Wind speed: 1800 RPM Bearings: liquid bearing Noise: 18 dBA Wattage: 1.5w Product Features The bottom is filled with copper, and the 40mm copper bottom contacts the CPU, resulting in faster and more effective heat dissipation. Silent fan, using hydraulic technology, with high air volume and no noise The humanized design with a product size of 67 high is suitable for 90% of chassis, home, office, internet cafe, and server products in the market.

Product features: The speed of the fan [with four wire temperature control and speed measurement chip] automatically adjusts the speed according to the working temperature of your CPU to achieve silence To ensure the stable operation of the system. The heat sink is made of high-precision frosted aluminum material with exquisite workmanship, making it a high-quality fan! Installation method of original fan The Intel original fan adopts a downward pressure fan design, and the original fan itself comes with silicone grease, so it can be installed directly (without the need to apply silicone grease again). After installing the processor, proceed with the installation of the fan. Step: Organize the fan When organizing the fan, it is important to pay attention to the position of the fan power cord and fastener button. The cord should be sorted out in advance to avoid any contact between the fan and the cord during operation. The initial position of the power cord is usually inside the fan (it can be removed). Note that the black raised dot on the buckle button as shown in the figure should be close to the fan. If the knob is not close to the fan, please restore it. Step 2: Adjust the position of the radiator Place the heat sink in a suitable position, place the fan horizontally above the processor cover, and align the bottom of the buckle posts (pointed contacts) around the buckle with the four buckle points on the motherboard. The motherboard buckle holes of Intel processors are distributed near the CPU slots, and users can easily find them by observing the motherboard. Before installing the original Intel heat sink, it is important to check whether the rotary switch has fully returned to its original position (original position: the dot is next to the heat sink). Step 3: Press the buckle Due to the use of four fastener designs, the correct method for installing the radiator fastener is the "diagonal" press installation method. Sequential pressing can easily cause uneven force on the fan, making it difficult to press the other two fasteners. Note that when pressing the buckle button, extra force should be applied. When a clear clicking sound is heard, it indicates successful pressing. After installing the heat sink, we need to connect the power cord of the heat sink fan (4Pin connector of the fan) and plug it into the heat dissipation and power supply interface of the motherboard. Step 4: Remove the fan To remove the heat sink, first remove the power cord, separate the fan power cord from the motherboard, and then proceed with the removal of the heat sink buckle. Learn to install a heat sink while also being able to disassemble it. There are two points to note when disassembling an Intel original heat sink. 1. Rotate the protruding point of the fastener column counterclockwise towards the outside of the radiator in the direction indicated by the button. 2. Use your thumb and index finger to lift the rotated fastener column upwards, and then remove the four fasteners in sequence.

Product information product price list: CPU heat sink+built-in thermal conductive silicone grease+kraft paper box product Model: 12th generation 1700 Fan rated voltage: 12V Fan size: 80X80X25mm Overall product size: 98 * 98 * 58mm Product installation size: 45mm (using a chassis with a height limit greater than 4.5cm) Fan speed: 1000-3000RPM ± 10% Voice value: 12-30.5DBA ± 10% Bearing type: hydraulic bearing Heat sink material: copper aluminum combination Input power: 1.6W (MAX)

Fan installation method The fan adopts a downward pressure fan design, and the original fan itself comes with silicone grease, so it can be installed directly (without the need to apply silicone grease again). After installing the processor, proceed with the installation of the fan. Step: Organize the fan When organizing the fan, it is important to pay attention to the position of the fan power cord and fastener button. The cord should be sorted out in advance to avoid any contact between the fan and the cord during operation. The initial position of the power cord is usually inside the fan (it can be removed). Note that the black raised dot on the buckle button as shown in the figure should be close to the fan. If the knob is not close to the fan, please restore it. Step 2: Adjust the position of the radiator Place the heat sink in a suitable position, place the fan horizontally above the processor cover, and align the bottom of the buckle posts (pointed contacts) around the buckle with the four buckle points on the motherboard. The motherboard buckle holes of Intel processors are distributed near the CPU slots, and users can easily find them by observing the motherboard. Before installing the original Intel heat sink, it is important to check whether the rotary switch has fully returned to its original position (original position: the dot is next to the heat sink). Step 3: Press the buckle Due to the use of four fastener designs, the correct method for installing the radiator fastener is the "diagonal" press installation method. Sequential pressing can easily cause uneven force on the fan, making it difficult to press the other two fasteners. Note that when pressing the buckle button, extra force should be applied. When a clear clicking sound is heard, it indicates successful pressing. After installing the heat sink, we need to connect the power cord of the heat sink fan (4Pin connector of the fan) and plug it into the heat dissipation and power supply interface of the motherboard. Step 4: Remove the fan To remove the heat sink, first remove the power cord, separate the fan power cord from the motherboard, and then proceed with the removal of the heat sink buckle. Learn to install a heat sink while also being able to disassemble it. There are two points to note when disassembling an Intel original heat sink. 1. Rotate the protruding point of the fastener column counterclockwise towards the outside of the radiator in the direction indicated by the button. 2. Use your thumb and index finger to lift the rotated fastener column upwards, and then remove the four fasteners in sequence. Intel Original Fan Installation Considerations: Firstly, prepare for the installation of the radiator; Reset the knob on the radiator buckle; Press the knob diagonally to secure the radiator; When uninstalling the processor, be sure to first unplug the fan power interface, and then rotate the knob counterclockwise to disassemble the fan. Before shooting, please carefully check what interface of the CPU you are using to avoid making mistakes. If you are purchasing in bulk, we will ship in 5 individual boxes with separate packaging, including the original box, instructions, and Intel small labels. Welcome to negotiate!

Product description Product information Product Price List: CPU Radiator+Kraft Paper Box Product model:LFB-115-36 Rated voltage of fan: 12V Fan size:90 X90 X25 mm Overall product size: 115 * 100 * 75m Product installation size: 45mn (with a height limit greater than 4 5cm chassis) Fan speed:2400 Å 10% RPM Voice value:23.5DBA Bearing type:Hydraulic bearings Heat sink material:AL6063 Input power:2.5V Bare metal weight:135g Finished product weight:160g Applicable platforms:Intel 1156/1155/1151/1150/1200/775

Under typical load conditions, the efficiency can reach up to 82%, which is more energy-efficient. 2. High speed current dynamic adjustment rate, with an adjustment time of up to 50us, making it more powerful. 3. Intelligent temperature control, with a minimum speed of 1000 rpm and quieter sound. 4. The minimum wide input voltage is 90-135/160-264V, which can be started in remote low-voltage areas, The switching switch conforms to the global voltage input, providing more peace of mind. 5. Dual tube forward topology, more stable. 6. Equipped with long line output, supporting back wiring for greater convenience. 7. Safety process design, anti radiation, anti-interference, etc., for greater safety. 8. Highly integrated IC circuit design, lower power consumption. 9. Adopting high-quality accessories for longer lifespan. 10. Supports the configuration of all motherboards and CPUs using ATX power supply on the market, making it more compatible. Other important feature highlights: ★: Equipped with super silent function: Intelligent fan speed control, optimal heat dissipation and silence processing, low noise, temperature control performance Stable; The circuit can automatically adjust and control according to the load size, input voltage level, and environmental temperature changes Fan speed). ★: Complete protection functions: AC undervoltage protection (Brown out), output overvoltage protection (OVP), output undervoltage protection (UVP), output overcurrent protection (OCP), overvoltage protection (OPP), short circuit protection (SCP), Anti Static (ESD), Lightning Surge, Magnetic Field Interference (EMC). ★: In response to the low power consumption demand of the new motherboard, the minimum load of each DC group is set to 0A output, which meets the minimum startup requirement Dynamic conditions. ★: The inductor adopts a high temperature characteristic and low power consumption Core. ★: Prepare PPFC with a power factor>0.75. ★: Low ripple: 5vs 3.3v, 5v<50mv, 12v<120mv, low ripple design, extending the lifespan of the motherboard Lifetime and reducing hard drive corruption. ★: Excellent LAYOUT design, with high-performance electromagnetic immunity capabilities such as resistance to lightning strikes (large), static electricity (ESD), external radiation (RS), external conduction (CS), and fast electrical burst (EFT). ★: Smaller Y capacitor design reduces the feeling of electric shock caused by leakage current. ★: High speed dynamic response mutation performance, able to handle high current and high-speed current mutation when graphics cards and CPUs are working Situation. ★: PCI-E 6+2 pin supports mid to high level graphics cards, paired with PCI-E graphics card dedicated connectors; 6+2 pin design supports Hold a 6-pin or 8-pin graphics card.

Under typical load conditions, the efficiency can reach up to 82%, which is more energy-efficient. 2. High speed current dynamic adjustment rate, with an adjustment time of up to 50us, making it more powerful. 3. Intelligent temperature control, with a minimum speed of 1000 rpm and quieter sound. 4. The minimum wide input voltage is 90-135/160-264V, which can be started in remote low-voltage areas, The switching switch conforms to the global voltage input, providing more peace of mind. 5. Dual tube forward topology, more stable. 6. Equipped with long line output, supporting back wiring for greater convenience. 7. Safety process design, anti radiation, anti-interference, etc., for greater safety. 8. Highly integrated IC circuit design, lower power consumption. 9. Adopting high-quality accessories for longer lifespan. 10. Supports the configuration of all motherboards and CPUs using ATX power supply on the market, making it more compatible. Other important feature highlights: ★: Equipped with super silent function: Intelligent fan speed control, optimal heat dissipation and silence processing, low noise, temperature control performance Stable; The circuit can automatically adjust and control according to the load size, input voltage level, and environmental temperature changes Fan speed). ★: Complete protection functions: AC undervoltage protection (Brown out), output overvoltage protection (OVP), output undervoltage protection (UVP), output overcurrent protection (OCP), overvoltage protection (OPP), short circuit protection (SCP), Anti Static (ESD), Lightning Surge, Magnetic Field Interference (EMC). ★: In response to the low power consumption demand of the new motherboard, the minimum load of each DC group is set to 0A output, which meets the minimum startup requirement Dynamic conditions. ★: The inductor adopts a high temperature characteristic and low power consumption Core. ★: Prepare PPFC with a power factor>0.75. ★: Low ripple: 5vs 3.3v, 5v<50mv, 12v<120mv, low ripple design, extending the lifespan of the motherboard Lifetime and reducing hard drive corruption. ★: Excellent LAYOUT design, with high-performance electromagnetic immunity capabilities such as resistance to lightning strikes (large), static electricity (ESD), external radiation (RS), external conduction (CS), and fast electrical burst (EFT). ★: Smaller Y capacitor design reduces the feeling of electric shock caused by leakage current. ★: High speed dynamic response mutation performance, able to handle high current and high-speed current mutation when graphics cards and CPUs are working Situation. ★: PCI-E 6+2 pin supports mid to high level graphics cards, paired with PCI-E graphics card dedicated connectors; 6+2 pin design supports Hold a 6-pin or 8-pin graphics card.

1. Under typical load conditions, the efficiency is 78%. 2. High speed current dynamic adjustment rate, with an adjustment time of up to 50us, making it more powerful. 3. The minimum speed is 1050 revolutions. 4. The minimum broadband input is 164~264V, which can be started in remote low-voltage areas, Voltage switching switches can be added to meet the voltage input in global high-voltage regions, making it more reassuring. 5. Adopting ordinary half bridge topology. 6. It can be equipped with long line output and supports back wiring for middle and lower boxes. 7. Safety regulations and processes, radiation prevention, anti-interference, etc. 8. Highly integrated IC circuit design, lower power consumption. 9. Use domestic ordinary accessories. 10. Supports the configuration of all motherboards and CPUs using ATX power supply on the market, making it more compatible. Other important feature highlights: ★: Complete protection functions: AC undervoltage protection (Brown out), output overvoltage protection (OVP), output undervoltage protection (UVP), overvoltage protection (OPP), short circuit protection (SCP), anti-static (ESD), lightning strike (Lighting SURGE). ★: In response to the low power consumption demand of the new motherboard, the minimum load of each DC group is set to 0A output, which meets the minimum startup requirement Dynamic conditions. ★: Install PPFC with a power factor>0.76. ★: Can be equipped with output capacitors, low ripple design, extending the service life of the motherboard and reducing hard drive corruption. ★: Excellent LAYOUT design, with high-performance electromagnetic immunity capabilities such as resistance to lightning strikes (large), static electricity (ESD), external radiation (RS), external conduction (CS), and fast electrical burst (EFT). ★: Smaller Y capacitor design reduces the feeling of electric shock caused by leakage current. ★: High speed dynamic response mutation performance, capable of handling high current and high-speed current mutation situations during CPU operation. ★: Above 250W can be paired with PCI-E graphics card dedicated connector

1. Under typical load conditions, the efficiency is 78%. 2. High speed current dynamic adjustment rate, with an adjustment time of up to 50us, making it more powerful. 3. The minimum speed is 1050 revolutions. 4. The minimum broadband input is 164~264V, which can be started in remote low-voltage areas, Voltage switching switches can be added to meet the voltage input in global high-voltage regions, making it more reassuring. 5. Adopting ordinary half bridge topology. 6. It can be equipped with long line output and supports back wiring for middle and lower boxes. 7. Safety regulations and processes, radiation prevention, anti-interference, etc. 8. Highly integrated IC circuit design, lower power consumption. 9. Use domestic ordinary accessories. 10. Supports the configuration of all motherboards and CPUs using ATX power supply on the market, making it more compatible. Other important feature highlights: ★: Complete protection functions: AC undervoltage protection (Brown out), output overvoltage protection (OVP), output undervoltage protection (UVP), overvoltage protection (OPP), short circuit protection (SCP), anti-static (ESD), lightning strike (Lighting SURGE). ★: In response to the low power consumption demand of the new motherboard, the minimum load of each DC group is set to 0A output, which meets the minimum startup requirement Dynamic conditions. ★: Install PPFC with a power factor>0.76. ★: Can be equipped with output capacitors, low ripple design, extending the service life of the motherboard and reducing hard drive corruption. ★: Excellent LAYOUT design, with high-performance electromagnetic immunity capabilities such as resistance to lightning strikes (large), static electricity (ESD), external radiation (RS), external conduction (CS), and fast electrical burst (EFT). ★: Smaller Y capacitor design reduces the feeling of electric shock caused by leakage current. ★: High speed dynamic response mutation performance, capable of handling high current and high-speed current mutation situations during CPU operation. ★: Above 250W can be paired with PCI-E graphics card dedicated connector